Briggs And Stratton Pressure Washer Carburetor Diagram [Visual Representation]
It’s not uncommon that the carburetor becomes clogged over time as it collects lots of dirt, dust, grease, etc. When blockages build up in it, you have to unclog or clean the carb. Therefore knowing the Briggs and Stratton pressure washer carburetor diagram is essential for you. The diagram will help you to understand what parts are included in the carb and how they work.
Throughout this diagram, we point out each part of the carburetor by marking it 1, 2, 3, etc. Also, we explained which number means what parts in the diagram.
So what are you waiting for? Sharply go through this article and learn the details:
Let’s Check The Briggs And Stratton Pressure Washer Carburetor Diagram
You will understand things better through the visual representation instead of just reading about it. So, before attempting to fix your carb’s clog or any other issue, it’s really wise to go through the diagram of it. For this purpose, we presented the diagram of the Briggs and Stratton pressure washer carburetor below. Let’s go through it:
| Parts Number | Meaning |
| 1 | Fuel bowl gasket |
| 2 | Primer bulb |
| 3 | Fuel bowl |
| 4 | Pin |
| 5 | Carburetor body |
| 6 | Hook pin |
| 7 | Welch plug |
| 8 | Hinge pin |
| 9 | Hinge pin |
| 10, 11 | Float |
| 12, 13 | Carburetor repair kit |
| 15 | Float needle |
More About Briggs And Stratton Pressure Washer Carburetor
Briggs and Stratton pressure washer’s crucial part is the carburetor. In fact, in the engine’s overall performance, the carburetor’s importance is behind the description. The carburetor’s essential parts are the fuel bowl gasket, primer bulb, fuel bowl, carburetor body, pin, welch plug, needle, etc. Usually, the carburetor contains a 15-piece set.
Any dirt deposits in the carburetor inside create the fuel, and air passages clog. It dramatically reduces the engine’s performance or stops the machine altogether. The carb can become clogged over time. When it gets blocked, the engine fails to get enough fuel. Consequently, the engine may run poorly or won’t start.
When your engine cranks or turns over or runs lean, be sure that the carb jet becomes clogged. And once the carburetor becomes blocked, you must unclog it to ensure your engine’s best performance. Luckily you can unclog or rebuild the carburetor.
However, you can unclog the carb properly by following the steps by steps ways below:
Step 1: First off, shut off the fuel valve and get access to the carburetor.
Step 2: Empty the gas tank. Then remove the carburetor and residual gas
Step 3: Take apart each part of the carburetor. Afterward, apply the carburetor cleaner and finally reassemble the unit’s all parts.
However, if you want to unclog the carburetor without taking its part apart, you can also do that. Just vacuum away the dirt, debris, foreign objects, or grime on the carb surface. You can use a handheld and cordless vacuum to clean it.
After cleaning or unclogging the carburetor, if the engine still performs poorly, it signals that the carb has become damaged. The carb can damage over time due to corrosion in it. So, now you have to replace the washer pressure carb.
The carburetor’s average replacement cost is $30-$200, including the labor and parts charge. The replacement cost can vary depending on different factors.
Frequently Asked Questions (FAQs)
Yes! You can use the WD40 for cleaning the carburetor. It’s safe to use for your device. Moreover, the dual action cleaning system of WD40 allows you to clean the throttle body, carb, and the machine’s unpainted metal parts.
Four signs will tell you that the carb has become defective. And these are reduction in engine performance, engine overheats or backfires, black smoke exhaust, and starting difficulty.
First off, start the cleaning process by checking the air filter. Ensure that clean air is coming into the carburetor. Also, ensure that the air filter is free of debris. Secondly, check the linkages. And finally, remove the carburetor’s clogs, deposits, dirt, or debris build-up by using the cleaner.
Wrap Up
Clog carburetor causes the engine’s sluggish performance, overheating, or reduced mileage. Therefore to avoid this unwanted situation, you must clean the carb’s clog. While you attempt to unclog or replace your carb by taking its parts apart, you need to know the details of it.
Hopefully, this article on the Briggs and Stratton pressure washer carburetor diagram helps you to learn the details of carburetor’s each part. But still, after going through the above details, comment in the comment section if you have anything to know.
You Can Also Read:
