The Karcher Pressure Washer No Pressure Issue
Karcher pressure washer is one of the budget series pressure washer one can have. With all its positive sides, it can still be a pain in the neck for you. We have heard people complaining about the Karcher pressure washer no pressure issue.
This no pressure issue can happen due to not having a proper water supply, or the nozzle might be having some hitches.
Well, this is pretty common, and you can troubleshoot the errors on your own. Some fixes might require professional supervision.
Today we will talk about pressure problems in Karcher washers and how to fix them. Without further ado, let’s start.
Karcher Pressure Washer No Pressure Problem And Fixes
No pressure from the washer is a problem that can take you off guard and make you wonder what now? Don’t stress, this happens to most people who use a pressure washer.
This is a more severe problem as you won’t get any water flow from the machine even if it’s running.
Here are some possible errors that can lead to no pressure
1. Blocked Nozzle Tip
Sometimes the clogged nozzle can be so harsh that it won’t even allow any flow. In that case, the cleaning method is the only solution.
You can do this by disconnecting the wand from the washer. Use a solid wire to take out the stuck debris.
Now you have to flush water back to the nozzle and then reconnect the wand to the unit. Turn on the unit and depress the trigger to see if everything is working or not.
2. Worn Nozzle
Karcher pressure washers usually come with more than one nozzle for various functions. If you overuse one nozzle for all the tasks, then don’t complain about it going bad. Excessive usage can take a toll on the nozzle and eventually degrade it. We are not talking about clogs, but rather complete deterioration.
What to do: You must switch the nozzle with the spare one. Switching to a good nozzle will do the trick.
3. Damaged Hose
If there are any leaks in the pressure hose or the garden hose, the output will be hampered. It’s wise to check both hoses for any possible leak.
Fixed: You will need couplings to seal the area or go for a complete replacement. For mending the leak, first, locate the leak and use a marker to mark the spot. Get a sharp blade to cut out the leaking area. Use the couplings and attach them to the slotted area and reattach the two ends. Bingo!
If this is too much for you, then get the hoses replaced with functioning ones.
4. Stuck Ports
The main port that connects the hose can be clogged and start to underperform. You should check all the ports that connect the high-pressure hose and garden hose. See if there is any debris piling up. If so, clean the area and reattach them.
5. Air Trapped In The Unit
If there is any air caught up in the machine, it may stop the water flow and you might observe no pressure from the outlet. Just as we mentioned you have to bleed out the unit to remove any trapped air.
When there is air in the system, you better bleed the washer to take off the unwanted air. First, you have to put the garden hose into the washer. Make sure the high-pressure hose is not attached.
Start the hose tap and flush the water into the system. Continue this for a minute or two. Now shut out the water flow and disconnect the line. Finally, connect the high-pressure hose, and you are done bleeding the system.
6. Running Below Optimum GPM
All pressure washers have certain GPM limitations. The GPM determines the amount of water flowing per minute. If you run the unit in a lower setting than the manufacturer’s mentioned rating, then the pressure might be low or none.
How To Find GPM Of Your Source: You will need a 1-gallon container for the measurement. Put it under the water outlet and turn the source on. Use a stopwatch and measure how long it takes to fill the container. Divide your reading by 60 and you will get the GPM reading of your water source.
7. Worn out O-Rings
If your washer’s O rings are damaged, it will prevent the water from coming out properly. In that case, you will have to replace the O rings.
Fixed: First, remove the pressure nozzle from the pump. Then remove the old rings from the nozzle. Take the new rings and lubricate them before putting them into the slotting. Re-install the pressure nozzle and the machine is good to go.
8. There Might Be Something Wrong With The Water Inlet Filter
A water filter is a key component in a pressure washer. It helps the washer provide clean water and last longer. If it gets dirty then you better clean it using clean water to remove dirt. If damaged, then replace it with a new one to restore optimum pressure.
Solution: You can also replace the filter if things don’t work and all should be good. Apart from these, you can also check the unloader valve and the pump. Sometimes malfunctioning water pumps or bypass unloader valves can make issues in building pressure.
Conclusion
If you ever come across a Karcher pressure washer no pressure dilemma, don’t worry. Be patient and try to diagnose the error by yourself. Cleaning the nozzle, bleeding the unit, replacing o rings, and cleaning the inlet filter can solve most problems.
That being said, we are dealing with a complex machine, and sometimes you might not be able to fix all issues by yourself. If there is internal damage, you should seek assistance from a professional mechanic who excels in repairing pressure washers.
You can always contact Karcher customer care specialists if you need warranty repairs. Best of luck!
You Can Also Read:
